Boards Switches Sensors

Select Your Harman Pellet Model

Showing 17–32 of 32 results

  • Harman & Heatilator Circuit Board D Shaped Knob & Shaft, 3 Pack, OEM

    Add to cart
  • Harman Retrofit Switch Kit for Hopper Extension, OEM

    Add to cart
  • Harman Touch Control, Touch Pad Circuit Board, TC Models, OEM

    Add to cart
  • Pellethead Replacement Harman & Heatilator Thermistor ESP Probe, Black Wire

    Add to cart
  • Harman & Heatilator ESP Thermistor Probe, Black Wire, OEM Quality

    Add to cart
  • Harman & Heatilator Furnace Circuit Control Board, OEM

    Add to cart
  • Placeholder

    Harman & Heatilator Eco-Choice Thermostat Wire, 2 Pair Twisted Cat 3 Cable, OEM

    Add to cart
  • Harman & Heatilator Eco-Choice Furnace Thermostat, OEM

    Add to cart
  • Harman & Heatilator Furnace Blower Fan Limit Switch, OEM

    Add to cart
  • Harman Wireless Room Sensor Thermostat, TC Models, OEM

    Add to cart
  • Harman & Heatilator Vacuum Differential Pressure Switch Silicone Tubing Hose, Aftermarket

    Add to cart
  • Harman & Heatilator EcoChoice Boiler Circuit Control Board Module, OEM

    Add to cart
  • Placeholder

    Harman PB105 & Heatilator Eco-Choice BH105 Outdoor Air Extension TCP, OEM

    Add to cart
  • Harman & Heatilator Aqua Temp, Air Temp Sensor Cable, OEM

    Add to cart
  • Harman & Heatilator Fuel Hopper Muffler & Fitting, Vacuum Safety Sensor, OEM

    Add to cart
  • Harman Platinum 4 Output Circuit Board Control Panel, OEM *REFURBISHED*

    Read more

Harman pellet stoves use a number of different control boards based on the model and year of manufacturer. The most common Harman control board is their ‘Platinum Board’ which is used on most automatic Harman stoves. This video will go through the operating modes and basic overview of the features and functions of this style Harman control board.

The vacuum or differential switch is a key component in making your Harman stove safe to operate.  The differential switch is also known as a vacuum switch.  The switch will measure the air pressure difference from inside the firebox.  Once this switch is activated it allows the feed system to kick in.   If you have an air leak from a door gasket, hopper lid, or a vent blockage this would cause the switch to open and prevent the stove from feeding.  Please watch the video below for more information.  If your board has a 2 blink error this is usually due to a failed vacuum switch or an air issue not allowing the vacuum switch to properly lock in.

The Harman ESP or Exhaust Sensing Probe is an advanced system used by Harman to measure how much heat the stove is producing out the exhaust to deliver precision heating control.  It will constantly monitor and adjust heat output to maintain set temperatures +/- 1 degree.  Some common symptoms of a bad ESP probe is your stove not shutting completely down after cooling, your distribution / room fan not turning on or off, or improper heat output based on your control board selections.  Your ESP may need to be replaced if your status light has a repeated 3 blink error. The below video illustrates how to clean and remove your ESP.

Another common sensor that Harman pellet stoves use is an RSP or room sensing probe.  If your stove operates on stove temp, but not on room temp, the likely culprit is a bad RSP.  These are inexpensive and easy to replace.  If you have a 4 blink error this is more than likely associated with a bad or unconnected RSP.